No Servers Will Connect But Ports Are Clear
#1
Posted 04 March 2016 - 05:16 AM
#2
Posted 04 March 2016 - 07:00 AM
1) server.met (http://upd.emule-security.org/server.met)
Download this to get all safe ed2k servers and place it inside config folder.
2) node.dat (http://upd.emule-security.org/nodes.dat)
Download this to get safe KAD nodes and place it inside config folder.
3) ipfilter.dat (http://upd.emule-security.org/ipfilter.zip)
Download this to block bad IP ranges and make sure you unzip the file and rename it to ipfilter.dat and place it inside config folder.
Now restart and connect, report back if you run into any issues.
#3
Posted 04 March 2016 - 08:50 AM
BlankArchiver, on 04 March 2016 - 08:16 AM, said:
There are about 10 good servers now. There are also some bad ones.
But even if you combine both, it would be far less than 150.
That is, most are dead in your list.
Delete all servers you have, and add peerates or gruk list.
Edit. emule-security list should be good enough too.
This post has been edited by fox88: 04 March 2016 - 08:52 AM
#4
Posted 04 March 2016 - 10:12 PM
#5
Posted 04 March 2016 - 11:17 PM
#6
Posted 05 March 2016 - 07:15 AM
1) Static NAT; You will have to first define the computer that will use ~Mule and give it reserved static LAN-IP on gateway, so it's LAN-IP address does not change as mostly its setup as default DHCP. You can do this under viewing all connected devices where you will find computer listed with current MAC, so give it reserved IP.
2) Add Service; Now open all the ports required by ~Mule to function under services make sure it match the protocol flag and internal device ip.
TCP port 4662 [in/out] is used for client to client transfer. (This is needed to obtain HighID on ED2K)
UDP port 4665 [in/out] is used for global server queries.
UDP port 4672 [in/out] is used for KAD and extended ED2K quires. (This is needed to obtain Ok status on KAD along side TCP 4662)
PS: If you still having problems post back regarding which part your confused on and ill try to walk you step by step.
#7
Posted 05 March 2016 - 08:34 AM
Could you finally learn something and drop that nonsense with default port numbers?
It is absolutely unnecessary step.
You just going againt all the instructions in this forum and in other places.
#8
Posted 05 March 2016 - 08:56 AM
PS: Please teach me networking. Take a photo of your networking switch that you built by hand and break it down from hardware to software how its implemented.
#9
Posted 05 March 2016 - 09:03 AM
#10
Posted 05 March 2016 - 09:16 AM
"You don't know enough to know that you don't know."
PS: Get back to me when they grant you tier2 access so you can finally for the first time in your life see LENS (Local Exchange Navigation System) interface from reputable OSS (Operational Support System) in EDIPC (Electronic Data Interchange Personal Computer) for information.
#11
Posted 26 July 2016 - 12:53 PM
ed2k://|server|46.105.126.71|4661|/ ed2k://|server|77.120.115.66|5041|/ ed2k://|server|85.204.50.116|4232|/ ed2k://|server|91.200.42.46|1176|/ ed2k://|server|91.200.42.47|3883|/ ed2k://|server|91.200.42.119|9939|/ ed2k://|server|119.29.53.207|443|/ ed2k://|server|176.103.48.36|4184|/ ed2k://|server|195.154.83.5|7111|/ ed2k://|server|195.154.128.49|4232|/ ed2k://|server|212.83.184.152|7111|/ ed2k://|server|222.85.25.33|40072|/
come ottenere aiuto italian guides - guide della sezione italiana
italian support - sezione italiana scaricare la lista server
ottenere id alto impostare le porte nel router
recuperare file corrotti i filtri ip
Sembra talco ma non č serve a darti l'allegrIa! Se lo lanci e poi lo respiri ti dā subito l'allegrIa!
#12
Posted 15 March 2017 - 09:47 PM
xSTHNSx, on 03 March 2016 - 11:00 PM, said:
1) server.met (http://upd.emule-security.org/server.met)
Download this to get all safe ed2k servers and place it inside config folder.
2) node.dat (http://upd.emule-security.org/nodes.dat)
Download this to get safe KAD nodes and place it inside config folder.
3) ipfilter.dat (http://upd.emule-security.org/ipfilter.zip)
Download this to block bad IP ranges and make sure you unzip the file and rename it to ipfilter.dat and place it inside config folder.
Now restart and connect, report back if you run into any issues.
#13
Posted 15 March 2017 - 09:51 PM
#14
Posted 15 March 2017 - 10:53 PM
- Highlight all those lines.
- Press the right button of your mouse and click copy in the context menu that should appear.
- Go to emule servers tab.
- Press the right button of your mouse when the cursor is in the servers area (the upper pane) and click paste ed2k links in the context menu that should appear.
- Now you should see 17 servers in your list.
For kad, check this post (click).
For ipfilter, this is not mandatory.
Anyway, you find the entry for it in options, security, update from url:.
come ottenere aiuto italian guides - guide della sezione italiana
italian support - sezione italiana scaricare la lista server
ottenere id alto impostare le porte nel router
recuperare file corrotti i filtri ip
Sembra talco ma non č serve a darti l'allegrIa! Se lo lanci e poi lo respiri ti dā subito l'allegrIa!